Line Fill & Knockout - Setup for Engraving

Line Fill & Knockout - Setup for Engraving

Postby MichelleMyBelle » August 5th, 2015, 4:35 am

We created a video for the Silver Bullet Pro cutting machine demonstrating engraving. In this video, we show how you can use the Line Fill along with Knockout effects to create a unique item. We also discussed the cutting set up that you'll need when using the Silver Bullet Pro cutting machine.

User avatar
MichelleMyBelle
 
Posts: 988
Images: 13
Joined: May 18th, 2011, 8:39 am
Location: PA
Cutter: Pro 18, Foil Master, Platinum 24"

Re: Line Fill & Knockout - Setup for Engraving

Postby mrsefs » August 8th, 2015, 4:49 pm

Is it possible to find out where you purchased the 4 x 4 metal tiles or the manufacturer?
Thanks in advance.
Kathy
mrsefs
 
Posts: 15
Joined: June 25th, 2015, 2:26 pm
Cutter: 13" Silver Bullet Pro Series

Re: Line Fill & Knockout - Setup for Engraving

Postby Gigi » August 8th, 2015, 4:58 pm

Not sure where they got them, but you can get a wide variety of tiles from Home Depot or Lowe's. Home improvement stores are a great resource! I have some fun faux brass tiles that I have been wanting to engrave and use for coasters (note to self - I need to do that!!)
Silver Bullet Admin/Tech Support


Happily using an 24" Silver Bullet Platinum

Gigi
User avatar
Gigi
 
Posts: 10432
Images: 190
Joined: May 14th, 2011, 9:53 pm
Location: Southern California
Cutter: 18" Silver Bullet Pro, Foilmaster

Re: Line Fill & Knockout - Setup for Engraving

Postby mrsefs » August 8th, 2015, 5:00 pm

I will have to stop in there tomorrow and see what I can find.
Thanks again.
Kathy
mrsefs
 
Posts: 15
Joined: June 25th, 2015, 2:26 pm
Cutter: 13" Silver Bullet Pro Series

Re: Line Fill & Knockout - Setup for Engraving

Postby Gigi » August 8th, 2015, 5:34 pm

Welcome - you can find all sorts of fun things there to play with ( check out the aisle where they keep the flashing too!) :)
Silver Bullet Admin/Tech Support


Happily using an 24" Silver Bullet Platinum

Gigi
User avatar
Gigi
 
Posts: 10432
Images: 190
Joined: May 14th, 2011, 9:53 pm
Location: Southern California
Cutter: 18" Silver Bullet Pro, Foilmaster

Re: Line Fill & Knockout - Setup for Engraving

Postby mrsefs » August 8th, 2015, 6:21 pm

I will do that, how do I know how thick the material can be? Do I measure an opening on the machine? I will go look through the learning center to see if I can find something about this. I'm excited to try this.
Kathy
mrsefs
 
Posts: 15
Joined: June 25th, 2015, 2:26 pm
Cutter: 13" Silver Bullet Pro Series

Re: Line Fill & Knockout - Setup for Engraving

Postby Gigi » August 8th, 2015, 6:37 pm

If you are engraving, the material just has to fit under the machine. We have had users engrave cell phone cases. Tiles easily clear the carriage unit, so no concern about them...
Silver Bullet Admin/Tech Support


Happily using an 24" Silver Bullet Platinum

Gigi
User avatar
Gigi
 
Posts: 10432
Images: 190
Joined: May 14th, 2011, 9:53 pm
Location: Southern California
Cutter: 18" Silver Bullet Pro, Foilmaster

Re: Line Fill & Knockout - Setup for Engraving

Postby scrappydew » August 9th, 2015, 5:26 pm

mrsefs wrote:Is it possible to find out where you purchased the 4 x 4 metal tiles or the manufacturer?
Thanks in advance.
Kathy



The box for the tiles say Handy Metal Wall Tiles - I found them on Amazon: http://amzn.to/1UxFmTg

The email on the back of the box says handytile@gmail.com Hope that helps you.
"If you always wait until the last minute... then it only takes a minute"
http://www.scrappydew.com
scrappydew
 
Posts: 77
Joined: July 9th, 2011, 8:33 pm

Re: Line Fill & Knockout - Setup for Engraving

Postby mrsefs » August 9th, 2015, 5:29 pm

That is great help, I really appreciate it.
Kathy
mrsefs
 
Posts: 15
Joined: June 25th, 2015, 2:26 pm
Cutter: 13" Silver Bullet Pro Series


Return to Broadcasts

Who is online

Users browsing this forum: No registered users and 11 guests

cron