Silver Bullet Cutters Forum

Lightly used 24" Silver Bullet Cutter

Includes:
24" cutter = $1199
24" table = $85
Click blade holder = $36
Detail blade holder = $40
Renu sheets = > $20
Original guide and personal guide (unused)

Value ~ $1400

Asking $999 with free shipping. We are taking a good loss on this, but we are moving into a different small business.

I am assuming that you are in the USA and bought from Sherri at That's Scrap, Inc. but you might want to clarify that. You might also want to tell when you bought it and thus if there is any warranty left on the machine. These are all important things I have seen buyers want to know in the past - especially in regard to any remaining warranty. If there is any, Sherri will usually transfer it with the machine as a courtesy to both the seller and the buyer. You will of course want to clarify that with her to be sure. Sounds like a great deal on a great machine. Hopefully someone will snap it up soon. (I'm tempted and I don't even NEED it! )

I apologize, I always forget to subscribe to my own threads (subscribed this time).

Thanks so much for all the useful pointers.

The item was bought at the start of 2015 in the USA from Sherri on That's Scrap, Inc. I'm not sure about warranty, I can look into that. Being that it is relatively new, I would guess that if warranty applied on other machines after transfer, this one should as well.

Let me know of any more info you want, I will respond quicker this time :p

Thanks,
John

Has this been sold?

Thanks!

(new here!)

Still available. Let me know if you have any questions

Hello!

I'm new here, and not used to the forum. How can we discuss this? Very interested!

I'm going to work on getting a video of it on and all the accessories today. Feel free to keep talking on here or in PM.

Thanks.

2lip wrote:Hello!

I'm new here, and not used to the forum. How can we discuss this? Very interested!

Welcome!

You can click on the PM box to the right and send the seller a private message and have a conversation if you like - or send them your email so you can more easily discuss it. Just showing how to do it privately if you would like.

Thanks!

I found the PM - must use full screen!

I have written back, hope it went thru!

thanks everyone!

Cyndi

You are welcome, Cyndi. Good luck!

I posted in PM, but figured I'd put here for more info on machine.

I will be selling:

- The 24" machine, in working order, we have used it to cut numerous things on multiple materials and it still works great. I got a new job and my wife doesn't want to sell paper products anymore.

- The table for the machine. This is incredibly useful (I wouldn't cut without it). It is a plastic piece that screws onto the front and back of the loading area of the machine and keeps the mat completely flat for good cutting.

- 3 different blade holders - There is the basic holder, the upgraded click holder (so you can quickly change the cutting depth), and the detail blade holder (this holds a smaller blade for making really detailed cuts on material).

- Renu sheets - these are for resticky-ing the mats, useful since the mats are somewhat expensive, so you can reuse them many many times before buying a new one. These mats are way better than the mats for Silhouette or Cricut (we've had them all).

- Original manual and personal guide (unused) - This has instructions for the cutter and the other manual has lots of space for you to put in info about what you cut and the settings you used. We never wrote in these so you are free to have/use them.

- A few other little things - We have the pen holder tool with a couple pens made for it, with this you can actual use the machine to 'draw' on material, we never used this, so it's all new

Things you will still need:
- Blades, any of these should work since we have all the blade holders http://thatsscrapinc.com/blades.aspx
- A cutting mat, I'd recommend this one http://thatsscrapinc.com/925x14silverbu ... 2-1-1.aspx
- Software, this came with machine but I can't personally transfer it. It is SureCutsALot, I believe there is a way to contact the owner of That's Scrap, Inc to get more info about this.

I'm going to get a video on the forum later tonight so you can see everything and show that it's all working. Let me know anything you want more info on.

Thanks for all of the updated info. Anyone purchasing a used machine should refer to this section so they can be sure to get the software and access to the learning center etc.http://forum.silverbulletcutters.com/viewtopic.php?f=32&t=5580

Thanks. . I didn't know about that. I'll have to get video soon. Things got busy today.

https://youtu.be/sa9-K6idt8I I just got the video up. Video just shows (in this order), the manuals, the renu sheets, the blades, the table, and then the machine. I just go through a couple simple actions on the screen to show it's working.

Let me know if you have any more questions.

Thanks.

This will be shipped for free in the original box. http://i.imgur.com/RWW0ihj.jpg

Edited to remove the image of the invoice for the privacy protection of the seller.

HI there... Is this still available? I'm very interested.

It is still available. Feel free to send any questions.

I would like to buy this machine. How do I get in contact with you jwenzler?

John has been watching this thread so if you do not hear back you can post here again. You can also click on the PM button on the right side of any of his posts and send him a message that you are interested - he will be notified via email that there is a PM for him on the forum.

Gigi wrote:John has been watching this thread so if you do not hear back you can post here again. You can also click on the PM button on the right side of any of his posts and send him a message that you are interested - he will be notified via email that there is a PM for him on the forum.

Thank you Gigi. I'm new here. I did sent a PM also. No reply yet. I've been dreaming with a SB for sooo very long. Would have A LOT to learn!! Hope I can get in contact with seller.
Regards